How to Choose a Ladder Safety Device

To stop a ladder sliding on the gutter, secure the top and the base. At the top, clamp the gutter edge, tie to a rigid support, or use a standoff. At the base, set up on firm ground at the right angle and secure the feet.

Three Ways to Secure the Top

How it works Needs Keep in mind
Clamp the gutter edge Clamps the ladder rail to the gutter lip A stable metal gutter with a lip Only use it if the gutter is stable enough to rest a ladder on
Tie to a rigid support Ties the ladder to a fixed point on the building structure A solid anchor point near the top The anchor must not bend or move
Use a standoff Holds the ladder off the gutter, resting on the roof or wall A roof or wall surface to rest on It doesn’t clamp the ladder in place

Clamp the Gutter Edge

A gutter clamp holds the ladder rail to the gutter lip, which helps stop the top sliding sideways.

Lock Jaw fits over the gutter lip and the ladder rail, and locks the two together. It has rubber pads that help protect the gutter and ladder.

Ladder fit
Lock Jaw accommodates ladder rails up to approximately 2 inches (50 mm) wide. It fits some, but not all, telescopic ladders; it depends on the make and model. If you’re unsure, send us your ladder model and we’ll help you check.
Gutters
It fits many metal gutter profiles, including traditional and K-style gutters, but not every gutter. The jaws must fit securely under the gutter lip, and the gutter must be sound and properly secured. The product requires the jaws to be clamped under the lip of a gutter and is therefore not intended for use on plastic gutters.
Leaf guards
If a leaf guard can be lifted it may be used; fixed metal leaf guards prevent the device from being applied.
Gutter condition
Recommended only if you are prepared to rest your ladder on the gutter; if the gutter is unstable it should not be used.

When to Choose a Standoff

A standoff attaches near the top of the ladder and rests on the roof or wall instead of the gutter.

  • You want no weight on the gutter. This suits gutter cleaning, gutter guard installs, or delicate gutters.
  • There’s no gutter at all. It can rest on a wall or roof edge.

Keep in mind that a standoff spreads your ladder’s contact at the top, but it doesn’t clamp onto anything.

Tie to a Rigid Support

If there’s a solid anchor point near the top, such as a fixed eye bolt in the building structure, you can tie the ladder to it.

  • Use a point that won’t bend or move. That rules out gutters, downpipes and gutter brackets.
  • Tie both rails if you can, so the ladder can’t swing to either side.
  • Check the tie before stepping on or off at the top.

This works best on buildings you access often, where an anchor point can be installed once and used many times.

Secure the Base

Securing the top is only half the job. A ladder can also slide out at the bottom.

  • Set up on stable, level ground.
  • Use leg levelers on uneven ground rather than propping a foot on bricks or timber.
  • Get the angle right. Set the base 1 foot out for every 4 feet of height.
  • Extend it above the roof edge. OSHA 1926.1053(b)(1): the side rails “shall extend at least 3 feet (.9 m) above the upper landing surface,” or the ladder must be secured at the top if it can’t.

What are base levelers?

Adjustable leg extensions on the bottom of the ladder. They keep it level on uneven ground, such as sloping lawns, garden beds or steps.

Whichever you use, the basics still apply:

  • Set the ladder at the right angle.
  • Check the ground is firm and level.
  • Inspect your gear before each climb.
  • Keep three points of contact.

Watch the fitting guide

How to Fit the Lock Jaw Ladder Grip

  1. Clip it to your belt with the included carabiner, so both hands stay free for climbing.
  2. At the top, place the jaws over the gutter edge with the bar over your ladder rail.
  3. Push the handle down with your palm. It locks in about five seconds, one-handed.